Brisket on Chopping Board with Knife and Fork

Where do I insert the Temperature Probe on a Brisket?

It takes some practice to prepare the perfect brisket, but a few straightforward tips from the masters can help you get started on your quest. One of the most helpful hints is learning how to probe a brisket to determine its level of doneness.

While some pitmasters can determine when a brisket is finished by looking at it, most people use a probe to check the internal temperature to prevent overcooking or undercooking continuously. We cover all the information you require regarding were to probe the brisket to determine when it is done in this article.

What are Point and Flat?

The location of the probe in the brisket is crucial. Away from the fat, the thickest part of the meat of brisket is the finest area to insert a probe. The densest section of the brisket, normally between the point and the brisket flat, should be in the middle of the probe.

When obtaining temperature measurements, it’s crucial to avoid probing the point, which is the fattier part of the brisket. The probe can readily entrap fat and provide you with erroneous readings. Make sure to insert the probe at an angle point, so it doesn’t touch any of the fat.

The flat is the leaner part of the brisket that is easier to probe. When taking temperature readings, however, ensure you’re in the densest part of the flat.

Where to Probe Brisket: A Brief Answer

The thickest part of the flat is the best place to check a brisket. 

Cross it over the grain by inserting it horizontally. The point will provide a less precise reading than the center due to its fat and connective tissue. If you want to be precise, probe in the flat!

Regarding meat probes, technology has advanced significantly; we recommend the temperature probe listed below. You leave the probe in the meat while it cooks, it connects to your phone via wifi, and the app has every cut of meat imaginable.

How Deep Should the Probe Be Inserted?

Most thermometers require you to insert the tip of the probe halfway. Of course, the thermometer you’re using makes a difference, and you can always consult the owner’s manual to learn how to use it properly.

For a thick cut of meat, such as brisket, insert it halfway into the meat, and it will ensure that you get an accurate reading.

How To Insert The Probe Into The Brisket

Inspect the brisket from the side, not the top. If you pierce the top of the brisket, all of the juices will escape, leaving your brisket dry. With the tip of your probe, pierce the side of the brisket halfway through.

The probe should be inserted at a 45-degree angle into the brisket’s center. Insert the probe into the brisket until it reaches the center. If you insert it too far, it will puncture the other side of the brisket, allowing all of the juices to escape.

When Should You Probe Brisket?

This question’s answer varies depending on the size of the brisket. A good rule of thumb is checking the temperature and probing the brisket after at least three hours of cooking. Of course, this will vary depending on the size of the brisket.

Smoking a brisket at temperatures ranging from 225 to 250 degrees Fahrenheit necessitates one to a half hours of cooking per pound. As a result, you can begin checking the temperature earlier for smaller briskets.

Probing the brisket meat should begin before it reaches an internal temperature of 165 degrees Fahrenheit or begins to stall. Check the temperature every 30 minutes or so at this point, or use your smart thermometer to alert you when it’s time to warp (Texas Crutch), if the brisket stalls, and when it’s done.

Why should you probe your brisket?

To cook the brisket properly, to the right doneness level, and end up with juicy, tender meat, you must prove it. Inserting a probe into the meat allows you to monitor the internal temperature and ensure it has been smoked while keeping the meat moist.

When cooking brisket, it is critical to monitor the internal temperature, so it does not overcook or undercook.

The Best Brisket Smoking Temperature

Brisket is best smoked at temperatures ranging from 225° F to 250° F. This will allow the brisket to break down all of its connective tissue and render the fat. Allow the brisket to develop a firm bark for the first 5 hours of cooking. When the bark is nice and crispy, wrap the brisket and cook until it reaches 200° F in the flat. Then, after a series of tenderness tests, rest the brisket for about an hour before slicing.

Final Thoughts

While you may never be able to determine the doneness of a brisket like a pitmaster, knowing where to probe brisket will help you achieve amazing results. When you learn how to probe brisket to check its internal temperature and tenderness, your barbecue skills will soar to new heights, and your friends and family will be impressed.


Featured Categories

About Me

Greetings BBQ & Brisket fans!

Since BBQ is now a professional career, I designed this website to turn you into a Brisket Pro. BBQ is more than a cooking style; it’s a lifestyle and art form. 

Read about how our community of grilling pros gets the perfect bark on our brisket or what grills and accessories we use. Plus, ask questions and find answers to your burning BBQing questions.